Media

Navigation

Browse albums
stressed exhaust bellows

stressed exhaust bellows

  • 0
  • 0
3 Bow Interior from Starbord View

3 Bow Interior from Starbord View

  • 0
  • 1
4 Bow Pic

4 Bow Pic

  • 0
  • 0
Side View

Side View

  • 0
  • 0
Sun Rotted interior. The dry storage ligs / seats were thrown out!

Sun Rotted interior. The dry storage ligs / seats were thrown out!

  • 0
  • 0
Peddle boat being lowered. I removed one holding rod (stb side) while leaving the port side rod connected to the boat.

Peddle boat being lowered. I removed one holding rod (stb side) while leaving the port side rod connected to the boat.

  • 0
  • 0
Built a peddle boat lift that can raise and lower the peddle boat into the water by using the stern drive. Made two rods and installed cleats on the p

Built a peddle boat lift that can raise and lower the peddle boat into the water by using the stern drive. Made two rods and installed cleats on the p

  • 0
  • 0
Bench seat. Removing old material and replacing with new grey vinyl that can take the odd spill. Also makes it easier when sliding into or out of the

Bench seat. Removing old material and replacing with new grey vinyl that can take the odd spill. Also makes it easier when sliding into or out of the

  • 0
  • 0
Added SS hinges to keep seat in place and make it easier for access.

Added SS hinges to keep seat in place and make it easier for access.

  • 0
  • 0
I cut the plywood in half before recovering. Don't have to remove the whole bench now to get access to storage.

I cut the plywood in half before recovering. Don't have to remove the whole bench now to get access to storage.

  • 0
  • 0
Lots of wasted space in the bow of a 2755. Got tired of setting up the v-berth and taking down to use as dinette. And then having to store the extra c

Lots of wasted space in the bow of a 2755. Got tired of setting up the v-berth and taking down to use as dinette. And then having to store the extra c

  • 0
  • 0
Using finnished 1x3 to frame the support.

Using finnished 1x3 to frame the support.

  • 0
  • 0
I removed all the carpet and fitted a 3/4" plywood to extend the platform to the edge of the seat base. This also provide extra storage.

I removed all the carpet and fitted a 3/4" plywood to extend the platform to the edge of the seat base. This also provide extra storage.

  • 0
  • 0
Added supports on each side that sits directly over the super structure so that there is access to storage below.

Added supports on each side that sits directly over the super structure so that there is access to storage below.

  • 0
  • 0
Port side support for V-berth.

Port side support for V-berth.

  • 0
  • 0
V-berth, purchased a 3" memory foam from Wallmart.

V-berth, purchased a 3" memory foam from Wallmart.

  • 0
  • 0
V-berth Trim installed, glue with SS screws and foam cut. The foam takes several days to expand to full size after pulling it out of the small box it

V-berth Trim installed, glue with SS screws and foam cut. The foam takes several days to expand to full size after pulling it out of the small box it

  • 0
  • 0
V-berth Trim with 1 coat of clear coat. I used 1/4" finnished plywood for the boxes and closed in the port side box, leaving the center and stb side o

V-berth Trim with 1 coat of clear coat. I used 1/4" finnished plywood for the boxes and closed in the port side box, leaving the center and stb side o

  • 0
  • 0
New V-berth completed. Table was also cut down to allow better access to seating.

New V-berth completed. Table was also cut down to allow better access to seating.

  • 0
  • 0
Re-powered OMC 5.8L in 2007 with a holley double pumper.

Re-powered OMC 5.8L in 2007 with a holley double pumper.

  • 0
  • 0
Map pouch.

Map pouch.

  • 0
  • 0
Finished look.

Finished look.

  • 0
  • 0
Removed stove cover and bolted to counter. Haven't desided what to do for trim, so just used tape.

Removed stove cover and bolted to counter. Haven't desided what to do for trim, so just used tape.

  • 0
  • 0
Stove was never used and I could never bring myself to lighting a fire inside the cabin using the alcohal burners. Removed the stove and capped the hy

Stove was never used and I could never bring myself to lighting a fire inside the cabin using the alcohal burners. Removed the stove and capped the hy

  • 0
  • 0
Top