Latest activity

What's new New posts Latest activity

C

cyclops222 reacted to HillbillyGuy's post in the thread I would like to take a moment to say thank you with Like.

I seldom find forums where folks try to help each other. There will always be disagreements and opinions on any given question or topic...

Tuesday at 7:58 AM
Lou C reacted to cyclops222's post in the thread Trim Continues Running After Releasing Button with Like.

I vote for a.......Magnetically sticking..... relay. Replace the relay.

Tuesday at 7:58 AM
Lou C replied to the thread 3.0 exhaust manifold over heats.

On the 3.0 cyl head the center cyls have the exhaust valves right next to each other so if the engine is running hot due to typical...

Tuesday at 7:57 AM
C

cyclops222 replied to the thread Trim Continues Running After Releasing Button.

I vote for a.......Magnetically sticking..... relay. Replace the relay.

Tuesday at 7:57 AM
Scott Danforth replied to the thread Owners Manual - 2006 Tahoe 215 Deck Boat - Outboard.

Look at the wire color and hope whitewater marine used ABYC wiring colors

Tuesday at 7:56 AM
C

cyclops222 reacted to Lou C's post in the thread Trim Continues Running After Releasing Button with Like.

Up relay getting stuck?

Tuesday at 7:55 AM
Scott Danforth replied to the thread Vinyl seat repair.

Best vinyl I have used is Sunbrella horizon. They have a 5 year anti-pinking warranty Today's treated lumber only lasts about 7-10...

Tuesday at 7:54 AM
D

dweese215 reacted to dingbat's post in the thread Owners Manual - 2006 Tahoe 215 Deck Boat - Outboard with Like.

Other than the hull, most components are outsourced through third party suppliers. As such, supplier information is typically not...

Tuesday at 7:35 AM
C

cyclops222 replied to the thread What should I offer on this outboard?.

Brand new bigger Yamaha O B have had massive delays waiting for GOOD NEW cast aluminum parts.

Tuesday at 7:33 AM
nola mike replied to the thread MC-1 Drive Dog failure?.

You got a lot going on. --Input shaft seal is responsible for the oil in the bellows. Where is the water coming from in the bellows...

Tuesday at 7:31 AM
ratdude747 replied to the thread MC-1 Drive Dog failure?.

Doing more reading, apparently the older drives (Alpha 1 gen 1 and earlier) don't use crush sleeves or rolling torque and instead use...

Tuesday at 7:27 AM
B

Brushape replied to the thread Lund 315 new to me - now what do I do?.

The transom is solid as it was redone. I am wondering about the stringer(s) etc but I will probably wait until next year before really...

Tuesday at 7:27 AM
ratdude747 reacted to Candy Gramformongo's post in the thread MC-1 Drive Dog failure? with Like.

Speedi Sleeve 99227 if you go that route. Mine had a groove that would not have polished out, and I bet yours will too. You don't even...

Tuesday at 7:25 AM
C

cyclops222 posted the thread Making a 16' Aluminum fish boat TOO LIGHT. in Boat Topics and Questions (not engine topics).

I finally did that last year. Moved the car battery from the small bow seat under the bow deck. To the transom compartment. BIG...

Tuesday at 7:24 AM
specialtrev posted the thread 2004 mercury 250sx rigging in Steering and Controls.

hey guys, im looking to find the controls and steering assembly for a 2004 250sx merc. i have had no luck tracking anything down any...

Tuesday at 7:21 AM

Show older items

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Latest activity

Follow Us