Latest activity

What's new New posts Latest activity

C

Chris1956 replied to the thread Spark plugs for a Merc outboard.

Gee, Champion spark plugs were used for decades in merc OBs. If memory serves, the BUHW-2 was equivalent to Champ L-78V, which was used...

Friday at 5:59 AM
Scott Danforth replied to the thread Sea-king Chrysler 15hp outboard motor does not start.

post a picture of the spark plug tester. because if it isnt an adjustable gap tester, you didnt test anything. does the spark look...
Friday at 5:49 AM
redneck joe replied to the thread daily music fix.

https://www.facebook.com/share/r/1BhaxmWkbB/

Friday at 5:42 AM
Scott Danforth replied to the thread BMW headlight . . . $1,000 !!!.

Hey Ted, used prices of headlights are about same as new for your car. also there are LED and Xenon listed for 2015 BMW's the Xenon...
Friday at 5:40 AM
Grub54891 reacted to airshot's post in the thread Lesson learned with Like.

The damn spell checker or whatever the setup is called that keeps changing my spelling is causing most of my spelling issues. Have not...

Friday at 5:35 AM
frustratedboater replied to the thread 1999 Johnson 200hp, Ocean Runner Lower Unit Hub.

No gears were replaced, but just the prop shaft. Everything is the same, the only replacement is the shim and the two o-rings on the...

Friday at 5:28 AM
jerryjerry05 replied to the thread Sea-king Chrysler 15hp outboard motor does not start.

If you have fuel coming out the exhaust snout?? Then you have put too much in or the fuel pump is defective.

Friday at 5:23 AM
dingbat replied to the thread N Y requires everyone to pass a powerboat operators license.

According to USCG records accidents had been on a downward trend for a number of years prior to Covid, then spiked again. Top causes...

Friday at 5:21 AM
jerryjerry05 replied to the thread Tillotson TC-5E float needle valve.

Years ago the factory service dept. issued a service bulletin. They suggested/said "set the air screws out at 1 turn and leave it there"...

Friday at 5:20 AM
jerryjerry05 replied to the thread Sealant for gearcase drive shaft and gear housing cap Shift shaft.

Just about anything you use will be ok. I use the High Tack. Google "gasket sealers" a bunch of them show. The first one is the old OMC...
Friday at 5:16 AM
alldodge replied to the thread 27PC - motor/pump sound from bow.

It's probably the relay and you need to remove the head board to get at it To verify before doing it, go to the engine room on the port...
Friday at 5:11 AM
alldodge reacted to SkaterRace's post in the thread Replacing my power block with Like.

Thanks I checked the wiring diagrams and I am pretty sure it is either a 6 or 8 gauge wire and a 96 inch run. Worse case says I should...

Friday at 5:05 AM
frustratedboater replied to the thread 1999 Johnson 200hp, Ocean Runner Lower Unit Hub.

Thanks for the reply.. 436740 OMC shaft was replaced. There are two thrust washers #30, and #44 on the prop shaft. I had spec'ed a...

Friday at 5:02 AM
M

MikeSchinlaub reacted to ratdude747's post in the thread Modifying a 1975 Trail-R-Craft with Like.

Winch came in and installed. Fit like a glove... and the action is way smoother with no slop or other baloney. Apparently, you do...

Friday at 4:45 AM
R

racerone replied to the thread 1999 Johnson 200hp, Ocean Runner Lower Unit Hub.

Explain ---" forward pump "----On this unit.----Part # of the gears you installed ?

Friday at 4:42 AM

Show older items

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Latest activity

Follow Us